Hoverstar Flight Technology Inc.

Contact Us

Name: Marie Lee
Tel: +86-755-33138076
E-mail: info@hoverstar.net
Add: Shenzhen,China
Skype: marielee08
WeChat: 哈威飞行
whatsapp: 008613527761074
Skype: marielee08 facebook: hoverstar facebook: HoverstarVideo facebook: hoverstar info@hoverstar.net

Support


Installation/Operation/Disassembly of AquaJet Dive

NOTE: Only adults are allowed to install/disassemble AquaJet Dive H2 and follow these steps.


 Disassembly Steps
1.(Optional) Remove the underwater camera.

2.Press the fast-assembling button to remove the wings.


3. Release the two lock catches on both sides of the head cover.



4. Unscrew the plug counterclockwise with the Allen wrench.


5. Use the inflator pump to inflate. After the gas nozzle is aligned with the plug hole , holding the head cover as you press the inflator pump to make the head cover slightly pop up, remove the head cover.

NOTE:
Make sure both sides of the lock catches have been released before inflating the pump.
While inflating, we recommend you to press the pump gently, ensure that the head cover will not pop out of the fuselage and cause product damage or personal injury!


6. (Optional) Take the clump weight out.


7. Disconnect the battery cables, remove the battery.

NOTE: Always work with dry hands while touching the battery and the junction to avoid battery short circuit.

8. After the charging port is plugged into the charger, connect the power supply. The red indicator light is on when charging and the green indicator light is on when the battery fully charged.

 
NOTE:
(1) Do not dispose of battery in a fire or heat the battery. Do not store the battery in high temperature.
(2) Do not reverse the polarity of the battery for any reason.
(3) Do not short-circuit the battery by using any metal objects such as wire directly.
(4) Do not drive a nail into the battery, strike it by hammer, tread or impact it by any other ways.
(5) Do not disassemble or modify the battery.
(6) Do not immerse the battery in water or get it wet.
(7) Use a lithium battery charger for charging, do not charge the battery under 0 ℃.
(8) When not in use for a long period of time, the battery must be charged and discharged at about every 2 months.
——end

 

Installation Steps

1. Remove the head cover.(See “Disassembly steps”, step3 to step5)
2. Put the battery into the battery compartment and connect the cables.


3.(Optional)Place the optional clump weight on the top of battery.


Note: It is easy to dive equipped with clump weight for deep divers.

4. Put the two sealing rings on the head cover.


5.Apply appropriate amount of Vaseline to the cover seal, install the head cover and press it.


6. Lock the locks on both sides of the head cover.


7.Tighten the vent plug clockwise with an Allen wrench.

NOTE: Apply appropriate amount of Vaseline to the plug to ensure the seal.

8. Install the left and right wings to the mounting position of the fuselage.


9. The electricity display and the green light is illuminated when pressing the left wing switch and keeping the pressure down, and the propeller begins to move when pressing the right speed button, which is normal working.
NOTE: The red light is illuminated when pressing the left wing switch, which means the battery is low. You need to recharge it before use.

10. (Optional) Install an underwater camera: fix the camera to the mounting hole with a joint.

——end


Operation Steps

1. Put the machine into the water, stretch your arms pass through the wrist strap respectively. 
2. Place your left hand on the left handle, and your right hand on the right  handle.


3. Your left hand press the switch ( keep pressing the switch) to power on, and your right hand press the speed button to start the machine.
4. Acceleration: The default speed of startup is the lowest, and there is a total of three gears: low speed, medium speed, high speed, followed by cycle. 
5. Dive: press down with your hands and enter into a state of diving.
6. Upward float: the two hands force up, enter swimming state.
7. Loosen the switch on left hand to shut down the product.
NOTE: The sediment should be prevented from entering the body and avoiding collisions.
——end

Online service

Skype: marielee08 info@hoverstar.net

Wechat

哈威飞行